Testimonials Testimonials

Pololu Step-Up 3.3V, 200mA Voltage Regulator NCP1402

£3.68
(£4.42 incl VAT)
Price in points: 736 points
1062-052
In stock
+

These tiny boost (step-up) switching regulators are based on the NCP1402 boost regulator IC. Their small dimensions of just 0.33″ × 0.5″ (8.4 mm × 12.7 mm) and a startup voltage of down to 0.8 V make it easy to build 3.3V circuits that are powered by lower battery voltages. The available output current and output voltage ripple depend on the input voltage (see Typical Efficiency and Output Current section below), but the regulator can provide up to 200 mA if the input voltage is high enough.

With low input voltages, the output voltage ripple is under 40mV peak-to-peak. When the input voltage is close to the output, the output ripple quickly climbs to 150mV peak-to-peak. Therefore, adding capacitance from the output to ground is recommended for noise-sensitive applications with input voltages close to the output voltage.

Some example applications include:

  • Powering 3.3 V or 5 V systems from lower-voltage batteries.
  • Powering higher-voltage subsystems in lower-voltage systems (e.g. powering a 5 V sensor in a 3.3 V system).

The boost regulator has just three connections: the input voltage, ground, and the output voltage. These three connections are labeled on the back side of the PCB and they are arranged with a 0.1″ spacing along the edge of the board for compatibility with standard solderless breadboards and perfboards and connectors that use a 0.1″ grid. You can solder wires directly to the board or solder in either the 3×1 straight male header strip or the 3×1 right-angle male header strip that are included.

Feature summary

  • Operating voltage: 0.8 V – VOUT
  • 3.3V output with 2.5% accuracy
  • <3 mA typical no-load quiescent current
  • Small size: 8.4 mm × 12.7 mm × 3.8 mm (0.33″ × 0.50″ × 0.15″)
  • Weight without header pins: 0.6 g (0.02 oz)

Typical Efficiency and Output Current

The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. As shown in the graph above, this switching regulator typically has an efficiency of 75% to 90%.

The maximum achievable output current is approximately proportional to the ratio of the input voltage to the output voltage. With a 0.8V input, approximately 5mA are available before the output voltage begins dropping. The full200 mA output can be realized from input voltages over approximately 2.4V (3.3 V version). Additionally, the maximum output current can depend on other factors, including the ambient temperature, air flow, and heat sinking.

LC Voltage Spikes

When connecting voltage to electronic circuits, the initial rush of current can cause damaging voltage spikes that are much higher than the input voltage. In our tests with typical power leads (~30″ test clips), input voltages above 4V caused voltage spikes in excess of 6V, the absolute maximum voltage of the NCP1402. You can suppress such spikes by soldering a 33μF or larger electrolytic capacitor close to the regulator between VIN and GND.

More information about LC spikes can be found in our application note, Understanding Destructive LC Voltage Spikes.

Dimensions

Size: 0.5" x 0.33" x 0.15"1
Weight: 0.6 g1

General specifications

Minimum operating voltage: 0.8 V
Maximum operating voltage: 3.3 V
Maximum output current: 200 mA2
Output voltage: 3.3 V
Reverse voltage protection?: N
Maximum quiescent current: 1 mA3

Notes:

1 Without included optional headers.
2 This is a function of the boost voltage: the greater the step-up voltage, the less current the unit can supply.
3 With no load. Actual quiescent current depends on input voltage.

Manufacturer's Details

Manufacturer's SKU :
2114
Manufacturer:
Pololu

No posts found

Write a review

No FAQ found

1062-036
£3.68 (£4.42 incl VAT)
1062-036
This compact (0.45″×0.6″) U1V11F3 switching step-up (or boost) voltage regulator efficiently generates 3.3 V from input voltages as...
In stock
Price in points: 736 points

Customers also bought....

1241-314
£0.16 (£0.19 incl VAT)
1241-314
A top entry shrouded 2.5mm header from the JST XH Series which has been designed specifically to provide high-density mounting for a range of miniature...
In stock
Price in points: 32 points

1241-324
£0.24 (£0.29 incl VAT)
1241-324
A side entry shrouded 2.5mm header from the JST XH Series which has been designed specifically to provide high-density mounting for a range of miniature...
In stock
Price in points: 48 points

2110-474
£1.74 (£2.09 incl VAT)
2110-474
A white 1W Silicon-lensed LEDs that feature high luminous flux with super energy efficient operation. Suitable applications for these LEDs include:...
In stock
Price in points: 348 points

1062-071
£11.07 (£13.28 incl VAT)
1062-071
This powerful step-up/step-down regulator efficiently produces a fixed 5V output from input voltages between 3V and 30V while allowing a typical output...
In stock
Price in points: 2214 points

1400-012
£2.84 (£3.41 incl VAT)
1400-012
This tiny DC motor produces vibrations by spinning an eccentric shaft at over 10,000 RPM when powered at 3 V. Motors like this are commonly found...
In stock
Price in points: 568 points