Save 67%

Pololu SPDT Relay Carrier PCB for Cube Relays

List price: £2.40
£0.80
(£0.96 UK, incl VAT) You save: £1.60 (67%)
Price in points: 160 points
3811-010
4 g
8 item(s)
End of Line
+
Add to wish list

Pololu’s basic relay carrier board makes it easy to incorporate a “sugar cube”-style power relay into your electronics project. An integrated MOSFET allows the relay to be controlled with a low-current digital input, and a pair of indicator LEDs show when the relay is activated. The three control pins have a 0.1″ spacing compatible with standard solderless breadboards and servo cables, and the switch pins are available for use with 5mm-pitch terminal blocks or 0.2″-spaced pins.

There are 5 variants to this product range, this basic PCB ready populated with the surface mounted components, two partial kits in both 5V and 12V relay versions and fully assembled units again in both 5V and 12V versions.

Note: This version is the PCB ready populated with the surface mount components, you will also need a relay and connectors of your choice. Suitable relays available in 5V, 12V & 24V versions..

The carrier board routes the three relay control pins to 0.1″-spaced pins compatible with standard solderless breadboads and female servo cable connectors. The relay switch pins are routed to a set of large pads intended for use with a 3-pin 5mm-pitch terminal block (ours have a slightly larger body than those supplied with the kits by Pololu but fine fine) and a set of smaller pads with a 0.2″ pitch, making them compatible with 0.1″ perfboards.

Advantages over similar products

  • Compact layout
  • Two LEDs to indicate coil actuation
  • Zener diode for fast current decay on relay coil
  • Specification of electrical routing clearance rules on relay switch nodes

Using the relay module

The switch portion of the relay is accessible on one side of the board while the control pins are routed to the other. The relay coil is powered by supplying the appropriate coil voltage for your specific relay across the VDD and GND pins, and it is activated by a digital high control signal on the EN pin. The control signal is fed directly to a BSS138 N-channel MOSFET, which in turn actuates the relay coil when the control voltage exceeds approximately 2.5 V (see BSS138 datasheet).

The relay switch terminals COM (common), NO (normally open), and NC (normally closed) are routed on the PCB with a minimum clearance of 60 mils (1.5 mm) from other copper. The copper traces are designed to be at least 45 mil (1.1 mm) from the board edges, though manufacturing variations in the board edges can make those distances slightly lower.

In most applications, the current and voltage ratings for the module will match the ratings of the relay used. Maximum current, maximum voltage, and life expectancy are interdependent; we therefore recommend careful examination of your relay’s datasheet.

Warning: This product is not designed to or certified for any particular high-voltage safety standard. Working with voltages above 30 V can be extremely dangerous and should only be attempted by qualified individuals with appropriate equipment and protective gear.

Schematic diagram

Click on thumbnail image above

Size

25 x 29mm

Downloads

Customers also bought....

3811-012
£3.77 £3.01 (£3.61 UK, incl VAT)
3811-012
Pololu’s basic relay carrier board makes it easy to incorporate a “sugar cube”-style power relay into your electronics project. An...
9 item(s)
End of Line

1063-077
£0.92 (£1.10 UK, incl VAT)
1063-077
4 x AA Enclosed Battery Box with Leads
In Stock

1400-023
£1.04 (£1.25 UK, incl VAT)
1400-023
Also known as a MM28   Specifications Voltage Range: 1.5V to 6V Rated Voltage: 3V Rated Power: 1.58W No Load Current:...
In Stock

1611-002
£1.16 (£1.39 UK, incl VAT)
1611-002
Miniature dry contact reed switch with rhodium contacts. Length 20.3mm Contact NO Contact rating 10VA Switching current 1A Carry current 1.5A DC switching...
In Stock

1611-010
£1.39 (£1.67 UK, incl VAT)
1611-010
Reed Magnet 12.7x3.2x1.6mm
In Stock