Testimonials Testimonials

Pololu Scooter / Skateboard / Skate Wheel Hub Adapter for 4mm Shaft

£3.52
(£4.22 incl VAT)
Price in points: 704 points
4609-134
In stock
+

This compact aluminum adapter assembly makes it easy to use many common scooter, skateboard, and inline skate wheels with motors with either a 4mm, 5mm or 6mm diameter output shaft depending on the version of adapter purchase. This enables many more wheel options for your project. It works with most wheels that are compatible with standard 608 bearings.

The adapter consists of two main components: a machined piece with threaded holes that mounts to the motor shaft using the two included M4 set screws, and a flat washer that clamps the wheel to the machined piece using the three included 14mm M3 screws. The washer has a hole in the center that allows the motor’s output shaft to optionally pass through for added flexibility in wheel placement on the shaft, and the low profile of the machined piece lets it work with wheels that have as little as 6mm of space between where the 608-series bearings normally fit.

Using the adapter

See the photo images above as well.

The adapter is straightforward to use when assembled in the proper order. First, slide the threaded shaft mount onto your motor’s output shaft with the narrower part facing away from the motor and tighten the set screws. (If your motor has a D-shaft, make sure you align the set screws with the flattened portion of the shaft.) Once this piece is secured, press the wheel directly onto it. Next, align the holes of the washer with the threaded holes of the shaft mount and press the washer into the recess on the other side of the wheel. The diameter of the washer is slightly smaller than that of the threaded shaft mount, so the orientation of the washer should be easier to adjust if the holes are not quite aligned. Finally, insert and tighten the M3 machine screws, making sure to tighten them evenly rather than one at a time.

Note: For some wheels, it might be difficult to push the washer into the wheel with your bare hands. In such cases, an alternative approach is to initially use longer M3 screws to engage the threads of the machined piece. You can then tighten the parts together, making sure to tighten the three screws evenly so that the washer stays parallel to the threaded piece. When the longer M3 screws cannot be tightened further, you can replace them with the included 14mm screws and finish the assembly.

You are recommended to check the adapter dimensions before purchasing to ensure the adapter will fit your wheels.

 

Downloads

Manufacturer's Details

Manufacturer's SKU :
2672
Manufacturer:
Pololu

No posts found

Write a review

No FAQ found

4609-135
£3.52 (£4.22 incl VAT)
4609-135
This compact aluminum adapter assembly makes it easy to use many common scooter, skateboard, and inline skate wheels with motors with either a 4mm, 5mm or...
In stock

4609-136
£3.52 (£4.22 incl VAT)
4609-136
This compact aluminum adapter assembly makes it easy to use many common scooter, skateboard, and inline skate wheels with motors with either a 4mm, 5mm or...
In stock

4611-050
£1.76 (£2.11 incl VAT)
4611-050
This is a black polyurethane scooter/skate wheel that measures 70mm in diameter and 25mm in width. These scooter wheels (also called inline skate...
In stock

4611-051
£2.10 (£2.52 incl VAT)
4611-051
This is a black polyurethane scooter/skate wheel that measures 84mm in diameter and 24mm in width. These scooter wheels (also called inline skate...
In stock

4611-053
£4.23 (£5.08 incl VAT)
4611-053
This is a black polyurethane scooter/skate wheel that measures 144mm in diameter and 29mm in width. These scooter wheels (also called inline skate...
In stock

Customers also bought....

4609-135
£3.52 (£4.22 incl VAT)
4609-135
This compact aluminum adapter assembly makes it easy to use many common scooter, skateboard, and inline skate wheels with motors with either a 4mm, 5mm or...
In stock

4609-040
£1.29 (£1.55 incl VAT)
4609-040
4mm Zinc Collets bright Zinc plated - pack of 4 including grub screws and matching hex key     Bore: 4mm     Overall...
In stock

4604-016
£0.37 (£0.44 incl VAT)
4604-016
A 4mm diameter shaft suitable for many of our plastic gears and sprockets. This steel shaft is coated but note the ends are simply cut and thus may need...
In stock

4609-114
£4.94 (£5.93 incl VAT)
4609-114
These universal mounting hubs are designed to work with most 4mm shafts, including round shafts, “D” shafts. Each of the two included hubs has...
In stock

4300-059
£1.42 (£1.70 incl VAT)
4300-059
These M1.6, pan-head screws are 3 mm long. They are made from zinc-plated steel and ship in packs of 6. These screws, which can be difficult to find,...
In stock