Testimonials Testimonials

Big MOSFET Slide Switch with Reverse Voltage Protection, MP

Pololu Big MOSFET Slide Switch Electronic Power Switch MP, 8A 4.5 to 40V

 
£3.67 incl VAT
(£3.06 exc. tax)
Price in points: 612 points
1614-509
8.00 g.
In stock
+
Add to wish list

The Pololu Pushbutton Power Switches are sophisticated power control alternatives to bulky mechanical switches. It uses a small integrated slide switch. Additional control inputs allow advanced applications such as automatic shutdown by the device being powered. This MP version operates from 4.5 V to 40 V and can deliver continuous currents up to around 8 A.

This product is a power switch implemented as a pair of P-channel MOSFETs configured as a high-side switch with reverse voltage protection and controlled by a micro slide switch. Because the main current does not go through the controlling mechanical switch, a variety of switches can be used without concern for the current they can carry. For example, a small slide or toggle switch can be mounted conveniently on a control panel with thin wires running to it, while the main power path can be shorter and with thicker wires. Pushbutton or tactile switches can also be used for momentary switching applications.

Unlike the Pololu Pushbutton Power Switches, which can lose their state when power is disconnected and reapplied, the conducting state of the MOSFET Slide Switches is determined only by the physical control switch (or a signal supplied to the “ON” pin), independent of power applied to the board. This can make them more appropriate for applications where the supplied power may be intermittent.

Warning: Do not use this switch as an emergency cutoff or similar safety disconnect in applications where failure to cut power could lead to injury or property damage.

Using the MOSFET Slide Switch

In the most basic application, power can be applied to the VIN and ground pins, with the on-board mini slide switch controlling power on the VOUT pins. To use an alternate SPST switch to control the MOSFETs, set the on-board slide switch to the off position and connect the alternate switch between ground and the switch control terminal, which is accessible both in the center of the board and along the side.

If the physical switch is in the “off” position, the switch state can also be controlled by a digital signal (e.g. from a microcontroller) via the “ON” control pin. Driving the “ON” pin low (or leaving it disconnected) will leave the switch off; driving the pin beyond approximately 1 V will turn the switch on. The maximum voltage for the “ON” pin is 30 V, independent of the switch voltage (VIN).

Each power node can be accessed through a large hole along the top side of the board or two smaller 0.1″-spaced holes along the sides of the board. For applications drawing more than 5 A, you should either use the large holes or both 0.1″-spaced holes for each power connection.

Included Hardware

Two 6-pin straight breakaway male headers and two 2-pin 5mm terminal blocks are included with each switch, and you can choose which of these components, if any, to solder to the board. The terminal blocks work with the four large holes, and the header strips allow the switch to be used with solderless breadboards and perforated circuit boards with standard 0.1″ spacing. If you want to use the terminal blocks, we recommend you install them on the side of the board without components, as shown in the above breadboard picture. The terminal blocks will cover one of each of the smaller VIN and VOUT holes, so you should not solder header pins into those holes if you plan on using terminal blocks.

Note that the terminal blocks are only rated for 16 A, so for higher-power applications, thick wires should be soldered directly to the board.

Thermal and power dissipation considerations

Because MOSFETs in the on state are effectively resistive, the power heating the board is proportional to the square of the current flowing through it. The comparison table near the top of this page shows typical currents that heat the MOSFETs to 55°C, where the MOSFETs start being noticeably warm but are still generally safe to touch, and currents that heat the MOSFETs to 150°C the absolute limit for the MOSFETs. With adequate cooling, or for brief periods if the MOSFETs are not hot to begin with, currents up to the listed maximums are attainable.

Transient protection

Interrupting large currents can cause voltage spikes (positive on the input side and negative on the output side) that depend on the inductance of the power connections and that can exceed the limits of the device. Appropriate measures to limit the size of these spikes include minimizing lengths of wires, placing capacitors at the power switch to smooth the spikes and absorb some of the energy, placing a schottky diode across the power output to absorb negative spikes, and placing a transient voltage suppressor (TVS) across the power input to absorb positive spikes.

Dimensions

Size: 0.8″ × 0.9″ × 0.16″1
Weight: 2.6 g2

General specifications

Current rating: 8 A3
Minimum operating voltage: 4.5 V
Maximum operating voltage: 40 V4
Reverse voltage protection?: Y

Identifying markings

PCB dev codes: psw04b
Other PCB markings: 0J9260

Notes:

1 Without included optional connectors. This also does not include the slide switch lever, which extends past the edge of the board by approximately 0.04″ (1 mm).
2 Without included optional connectors.
3 Continuous at 12 V, without exceeding 150°C.
4 Recommended maximum is 32 V.

No posts found

Write a review

No FAQ found

1614-510
£5.60 incl VAT (£4.67 exc. tax)
1614-510
This breadboard-compatible module is an alternative to bulky power switches. It uses a small integrated slide switch to control a high-side power MOSFET... read more
In stock
Price in points: 934 points

Customers also bought....

1451-109
£6.44 incl VAT (£5.37 exc. tax)
1451-109
These light-weight brackets are specifically designed for the Pololu 25D mm metal gearmotors , including the same motors used in the Wild Thumper... read more
In stock
Price in points: 1074 points

2110-678
£0.55 incl VAT (£0.46 exc. tax)
2110-678
A PCB mounting single transistor output slotted photo interrupter without mounting flanges and featuring an aperture comprising an infra-red emitter and... read more
In stock
Price in points: 92 points

3811-014
£4.70 incl VAT (£3.92 exc. tax)
3811-014
Pololu’s basic relay carrier board makes it easy to incorporate a “sugar cube”-style power relay into your electronics project. An... read more
In stock
Price in points: 784 points

4255-118
£0.82 incl VAT (£0.68 exc. tax)
4255-118
Ball Bearing: Bore 3mm Outer Diameter 8mm Width 4mm Load rating 558N read more
In stock
Price in points: 136 points

4308-420
£0.71 incl VAT (£0.59 exc. tax)
4308-420
A pack of 10 M4 x 20mm long Nylon 66 cheese head machine screws suitable for where insulated fixings are required or corrosive conditions. read more
In stock
Price in points: 118 points