Testimonials Testimonials

Pololu ACS711EX Current Sensor -31 to +31A

£2.62
(£3.14 UK, incl VAT)
Price in points: 524 points
3801-208
2 g
In stock
+

This board is a simple carrier of Allegro’s ±31A ACS711 Hall effect-based linear current sensor with overcurrent fault output, which offers a low-resistance (~0.6mΩ) current path and electrical isolation up to 100V. This version accepts a bidirectional current input with a magnitude up to 31A and outputs a proportional analog voltage centered at Vcc/2 with a typical error of ±5%. It operates from 3V to 5.5V, so it can interface directly to both 3.3V and 5V systems.

Overview

This current sensor is a carrier board or breakout board for Allegro’s ACS711KEXLT-31AB-T Hall effect-based linear current sensor with overcurrent fault output; we therefore recommend careful reading of the ACS711 datasheet (551k pdf) before using this product. This sensor has an operating voltage of 3V to 5.5V and an output sensitivity of 45mV/A when Vcc is 3.3V (or 68mV/A when Vcc is 5V). The following list details some of the sensor’s key features:

  • Designed for bidirectional input current from -31A to 31A (though the robust sensor IC can tolerate 100ms transient current spikes up to 100A).
  • Conductive path internal resistance is typically 0.6mΩ, and the PCB is made with 2-oz copper, so very little power is lost in the board.
  • Use of a Hall effect sensor means the IC is able to electrically isolate the current path from the sensor’s electronics (for applications up to 100V), which allows the sensor to be inserted anywhere along the current path and to be used in applications that require electrical isolation.
  • 100 kHz bandwith.
  • Good accuracy and reliability: factory calibration results in a typical total output error of ±4% at room temperature, the output offset voltage is extremely stable, and the sensor has zero magnetic hysteresis.
  • Overcurrent FAULT output latches low when current magnitude exceeds 31A.
  • Operating temperature range of -40°C to 125°C.

The pads are labeled on the bottom silkscreen. The silkscreen also shows the direction that is interpreted as positive current flow via the +i arrow.

This 15.5A current sensor is marked with a green X. We also sell a 15.5A version that uses the same carrier PCB; you can distinguish the versions by reading the text on the IC or by looking at the color of the X on the bottom silkscreen.

This sensor is very similar to the original ACS711 -25 to +25 A Current Sensor Carrier, but uses a smaller “EX” package that has a larger optimized sensing range and reduced internal resistance. The board size, pinout, and hole locations are all unchanged, so it can generally be used as a drop-in replacement for our ACS711 carriers with “LC” packages.

Using the sensor

Electrical connections

The sensor requires a supply voltage of 3V to 5.5V to be connected across the Vcc and GND pads, which are labeled on the bottom silkscreen. The sensor outputs an analog voltage that is linearly proportional to the input current. The quiescent output voltage is Vcc/2 and changes by 45mV per amp of input current (when Vcc = 3.3V), with positive current increasing the output voltage and negative current decreasing the output voltage.

The FAULT pin is normally high and latches low when the current exceeds ±31A. Once the FAULT pin is latched low, the only way to reset it is by toggling power on the Vcc pin. In tests, this module was able to handle 31A of continuous current without exceeding 100°C, with no cooling beyond the heat dissipation of the PCB.

The input current can be connected to the board in a variety of ways. Holes with 0.1″, 3.5mm, and 5mm spacing are available as shown above for connecting male header pins or terminal blocks. For high-current applications, you can solder wires directly to the through-holes that best match your wires, or you can use solderless ring terminal connectors, as shown in the picture. The large through-holes are big enough for #6 screws.

Warning: This product is intended for use below 30V. Working with higher voltages can be extremely dangerous and should only be attempted by qualified individuals with appropriate equipment and protective gear.

Mounting information

The board has two mounting holes on the logic side of the board. These mounting holes are 0.5" apart and are designed for #2 screws.

Included components

This board ships assembled with all surface mount components, and a 5×1 strip of 0.1″ header pins is included but not soldered in, as shown in the picture.

Manufacturer's Details

Manufacturer's SKU :
2453
Manufacturer:
Pololu

No posts found

Write a review

No FAQ found

Customers also bought....

4254-000
£0.42 (£0.50 UK, incl VAT)
4254-000
Type 6000 2RS 10mm bore, 8mm deep, 26mm O/D
In stock

1208-002
£0.17 (£0.20 UK, incl VAT)
1208-002
16A Interlocking Terminal Block 2-Way These 16A 250V terminal blocks on a 5mm pitch (0.2") can be interlocked together to make even longer blocks. Max...
In stock

1503-018
£10.04 (£12.05 UK, incl VAT)
1503-018
Overview Texas Instruments’ DRV8835 is a tiny dual H-bridge motor driver IC that can be used for bidirectional control of two brushed DC motors at 2 to...
Currently out of stock

4604-012
£1.94 (£2.33 UK, incl VAT)
4604-012
A precision 4mm diameter shaft x 150mm suitable for many of our plastic gears, sprockets, model bearings and model wheels. This steel shaft is, we believe,...
In stock

1450-057
£14.40 (£17.28 UK, incl VAT)
1450-057
MFA Como Drills 919D1001 Output @ 4.5V 59rpm Output @ 6V 79rpm, 11820g/cm at max efficiency, stall torque 67000g/cm Output @ 9V 119rpm Output @ 12V 158rpm...
In stock