Testimonials Testimonials

Pololu 700:1 Sub-Micro 6mm Plastic Planetary Geared Motor

£8.25
(£9.90 UK, incl VAT)
Price in points: 1650 points
1451-028
2 g
In stock
+

This tiny, cylindrical gearmotor consists of a coreless brushed DC motor and a 700:1 plastic planetary gearbox. The entire assembly has a diameter of just 6 mm (0.24″) and an extremely light weight of 1.2 g (0.042 oz), making it a great actuator for miniature robots and very small mechanisms.

Key specs at 6V: 90 RPM and 45 mA free-run, 12 oz-in (0.9kg-cm) and 400 mA stall.

Overview

These tiny brushed DC gearmotors have a diameter of just 6 mm and weigh just over a gram, which makes them great actuators for miniature robots and very small mechanisms. They consist of a coreless motor fastened to a planetary gearbox by a small clip. The gears are made from liquid crystal polymers (LCPs), and gearbox’s nylon output shaft is compatible with our 14 mm wheels. Several gear ratios are available:

  • 5.1:1, which has a free run speed of 13,000 RPM and stall torque of 0.3 oz-in (22 g-cm) at 6V
  • 26:1, which has a free run speed of 2500 RPM and stall torque of 1.5 oz-in (110 g-cm) at 6V
  • 136:1, which has a free run speed of 500 RPM and stall torque of 8 oz-in (550 g-cm) at 6V
  • 700:1, which has a free run speed of 90 RPM and stall torque of 12 oz-in (900 g-cm) at 6V

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. For these gearboxes, the recommended upper limit for instantaneous torque is 3.5 oz-in (250 g-cm); we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

The intended nominal operating voltage for these motors is 3V to 6V, though in general, these kinds of motors can be used at voltages outside this range (rotation typically starts between 0.2V and 0.3V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. When operating at 3V, the free-run speed, stall torque, and stall current will all be approximately half of what they are at 6V as these specifications scale roughly linearly with voltage.

Since the gearmotor’s output shaft is nylon, there can be small variances in the diameter from unit to unit. These variations might cause press-fit attachments like our 14 mm wheel to fit loosely in some instances. If you experience a loose fit, you could try swapping wheels or using a small dab of glue to help hold the wheel on.

Gearmotor dimensions

The following diagram shows the micro plastic gearmotor dimensions in mm. The planetary gearbox has a D-shaped plastic output shaft, which is 2 mm in diameter with a section that is flattened by 0.5 mm. The “D” portion of the shaft is 2.5 mm long. The motor measures 6 mm in diameter and 9.3 mm in length, and the gearbox length, labeled “L” in the diagram below, depends on the gear ratio.

Sub-micro gearmotor dimensions

Motor accessories

The micro plastic gearmotor’s output shaft is compatible with our 14 mm wheels. We do not have any brackets for this gearmotor, and it does not have any mounting holes, but its compact size makes it easy to fasten with tape or glue. Alternatively, since this gearmotor is nearly the same size as a 1/4″ fuse, it can be mounted using standard 1/4″ (6 mm) fuse clips.

No posts found

Write a review

No FAQ found